1、購買一個合適的電動門驅動器。可以根據門的尺寸和重量選擇合適的電動驅動器。

　　1. Purchase a suitable electric door driver. Suitable electric drivers can be selected based on the size and weight of the door.

　　2、關閉門，并確保門的運行順暢。如果門有任何故障或損壞，需要先修復。

　　2. Close the door and ensure its smooth operation. If there is any malfunction or damage to the door, it needs to be repaired first.

　　3、安裝電動門驅動器。根據驅動器的安裝指南，使用螺絲刀和電鉆將驅動器固定在門上。確保驅動器安裝穩固。

　　3. Install the electric door driver. According to the installation guide for the driver, use a screwdriver and drill to secure the driver to the door. Ensure that the driver is securely installed.

　　4、連接電動門驅動器的電源。根據驅動器的電氣連線圖，將電源線與驅動器連接。確保正確連接并固定線路。

　　4. Connect the power supply of the electric door driver. Connect the power cord to the driver according to the electrical wiring diagram of the driver. Ensure proper connection and secure of the circuit.

　　5、連接開關和遙控器。根據驅動器的電氣連線圖，將開關和遙控器與驅動器連接。確保正確連接并固定線路。

　　5. Connect the switch and remote control. Connect the switch and remote control to the driver according to the electrical wiring diagram of the driver. Ensure proper connection and secure of the circuit.

　　6、進行測試。打開電源，使用開關或遙控器控制門的開閉。確保門能夠順利運行，并檢查是否有任何異常。

　　6. Conduct testing. Turn on the power and use a switch or remote control to control the opening and closing of the door. Ensure that the door can operate smoothly and check for any abnormalities.

　　電動卷簾門突然打不開？

　　Electric rolling shutter door suddenly doesn't open?

　　一、卷簾門開啟困難，聲音刺耳

　　1、 The rolling shutter door is difficult to open and the sound is harsh

　　如果發現通電后卷簾門開啟困難并且發出嘈雜聲響，那原因極有可能是卷簾門上的簾片被導槽卡住或是簾片變形了。給出的解決辦法是，仔細對卷簾門入導槽的槽口處進行查看矯正維修。

　　If it is found that the rolling shutter door is difficult to open and makes a noisy sound after being powered on, the reason is most likely that the curtain on the rolling shutter door is stuck in the guide groove or deformed. The proposed solution is to carefully inspect, correct, and repair the groove at the entrance of the roller shutter door.

　　二、電動機不動或轉速慢

　　2、 Electric motor not moving or slow speed

　　此故障原因一般是線路斷路、電機燒損、停止按鈕沒復位、限位開關動作、負載較大等引起。

　　The cause of this fault is generally due to circuit breakage, motor burnout, failure to reset the stop button, limit switch action, high load, etc.

　　處理方法是檢查線路、并接通；更換燒損電機；更換按鈕或重復按動幾次；撥動限位開關滑塊使它脫離微動開關觸點，并調整微動開關位置；檢查機械部分有無卡阻，若出現卡阻則卡阻、清理障礙物。

　　The solution is to check the circuit and connect it; Replace the burnt motor; Replace the button or press it repeatedly a few times; Move the limit switch slider to disengage it from the microswitch contact and adjust the microswitch position; Check if there is any blockage in the mechanical part. If there is any blockage, eliminate it and clean up the obstacles.

　　三、卷簾門不能卷起來，呈圓柱狀

　　3、 The rolling shutter door cannot be rolled up and is cylindrical in shape

　　通電之后卷簾門呈圓柱狀且不工作，那么可能是內部彈簧折斷或是彈簧連接帶斷裂。出現這種問題就需要更換彈簧吊帶。

　　After being powered on, if the rolling shutter door is cylindrical and does not work, it may be due to a broken internal spring or a broken spring connecting strap. If this problem occurs, it is necessary to replace the spring sling.

　　四、卷軸運轉困難，開啟時感覺阻力

　　4、 The scroll is difficult to operate and feels resistance when opened

　　造成這種故障的原因是因為卷軸兩端口的不夠潤滑，與葉片產生阻力。解決辦法是在卷軸兩端均勻涂抹潤滑油。建議驅動器每年少要加注一次潤滑脂，鏈條應經常加注潤滑油，并檢查各部件磨損情況，磨損嚴重的機件要及時維修或更換。

　　The reason for this malfunction is due to insufficient lubrication at the two ports of the spool, which creates resistance with the blades. The solution is to evenly apply lubricating oil on both ends of the scroll. It is recommended to add lubricating grease to the drive at least once a year, regularly lubricate the chain, and check the wear of each component. Parts with severe wear should be repaired or replaced in a timely manner.

　　五、電機振動或噪聲較大

　　5、 Motor vibration or noise is high

　　出現這種情況的原因可能有剎車盤不平衡或斷裂；剎車盤無緊固；軸承失油或失效；齒輪嚙合不順、失油或磨損嚴重等這幾種故障點。處理方法是更換剎車盤或重新調整平衡；緊固剎車盤螺母；更換軸承；修配電機軸輸出端齒輪、潤滑或更換；檢查電機，如電機壞損則更換。

　　The reason for this situation may be that the brake disc is unbalanced or broken; The brake disc is not securely fastened; Bearing oil loss or failure; There are several fault points such as unsmooth gear meshing, oil loss, or severe wear. The solution is to replace the brake disc or readjust the balance; Tighten the brake disc nut; Replace bearings; Repair, lubricate or replace the gear at the output end of the motor shaft; Check the motor and replace it if it is damaged.

　　六、長期缺少保養引起閘門故障

　　6、 Long term lack of maintenance causes gate failure

　　電動卷簾門的感應探測器探測到有人進入時，就會將脈沖信號傳給主控器，主控器判斷后通知馬達運行，同時監控馬達轉數，以便通知馬達在一定時候加力和進入慢行運行。如果長期缺乏保養，導致電動卷閘門存在的隱患及小故障得不到及時處理，馬達得到一定運行電流后做正向運行，將動力傳給同步帶，再由同步帶將動力傳給吊具系統使門扇開啟；門扇開啟后由控制器作出判斷，如需關門，通知馬達作反向運動，關閉門扇。將會由小故障變成大故障，終可能導致自動電動門的癱瘓，因此定期對電動卷簾門進行保修是非常重要的。

　　When the induction detector of the electric rolling shutter door detects someone entering, it will transmit a pulse signal to the main controller. After judgment, the main controller notifies the motor to run and monitors the motor speed to notify the motor to apply force and enter slow running at a certain time. If there is a long-term lack of maintenance, the hidden dangers and minor faults of the electric roller shutter cannot be dealt with in a timely manner. After the motor receives a certain operating current, it runs forward and transmits power to the synchronous belt, which then transmits power to the lifting system to open the door leaf; After the door leaf is opened, the controller makes a judgment. If the door needs to be closed, it notifies the motor to move in the opposite direction and close the door leaf. It will turn from a minor malfunction to a major one, ultimately leading to the paralysis of the automatic electric door. Therefore, it is very important to regularly provide warranty for the electric rolling shutter door.

　　本文由  濟南卷簾門 友情奉獻.更多有關的知識請點擊  http://www.aimudiao.cn/   真誠的態度.為您提供為的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from Jinan Rolling Shutter Doors For more related knowledge, please click http://www.aimudiao.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.